亚洲一区二区精品,黄色软件视频免费,国产精品国产三级国产专不?,性福宝软件下载

本產品適用于化纖，尼龍布。調水漿需加10%—20%水洗牢度特強。

[性質]

外觀:乳白色液體

主成分:特殊樹脂

離子性:陰離子

含固量: 50%

[保質期]

室溫5-35℃,避免暴曬或受凍,一般可貯存1年。

1)易調色,色澤鮮艷飽滿。

2)牢度特好,耐水性特強,手感較柔軟,流動性好,覆蓋力強,花形輪廓清晰。

3)耐黃變(高溫下不易泛黃變色)。平整度好。

4）環保指數達國際環�？椢镆�求。

5）手搓不泛白，水洗后手感超柔軟，干濕摩擦牢度超好，干擦4級，濕擦3-4級。摩擦痕跡不明顯

[應用]滾筒、圓網、平網、手工印花和噴花多種工藝。

[操作工藝]

漿料+色漿+固色劑,根據實際情況調整(Mesh網布80-120目)印花→干燥

有條件：烘干、熱處理(130-150℃,3-5分鐘)效果更好。

[注意事項]每批次貨/每次使用前,必須認真試驗,確認后方可使用。

1)選擇合適的固色劑可以提高印花面的色牢度與摩擦牢度(注意固色劑的時效性) ,避免使用陽離子色漿和助劑。

2)干透后再進行熱處理,可以增加牢度。24-48小時后,方可測試?yán)味取?/span>

Other detailed information

This product is suitable for chemical fiber, Nylon.Adding 10% or 20% slurry to improve the washing fastness.

[Characters ]

Appearance :milky white liquid

Main component :special resin

Ionic : anion

Solid content : 50%

[shelf life]

At room temperature 5-35℃,avoid sun exposure or frozen, can be stored for one year as usual.

1)Easy to mix color,the color is bright and full.

2)Good fastness,super water resistance,soft hand feel,good fluidity,high coverage and clear outline.

3)Resistant to yellowing(it is not easy to turn yellowing at high temperature),good flatness.

4)The environmental indicators reach the requirements of international environmental textile .

5）After hand rubbing,not white,super soft hand feel after washing,excellent wet and dry rub,the dry rub is 4 degree,the wet rub is 3-4degree.The marks of friction are not obvious.

[Application] cylinder、rotary screen、flat screen、handcraft printing and spray.

[operation technology]

Paste+pigment+fixing agent,according actual situation to adjust(80-120mesh screen)printing→drying

If have condition:stoving、heat treat(130-150℃,3-5minutes)better effect.

[Notes] Every batch of goods /before each use, must have test and use after in certain condition.

1)Choosing appropriate fixing agent can improve the color fastness and friction fastness of printing surface(note the timeliness of fixing agent),avoid using cationic paste and auxiliaries.

2)After drying and then making heat treat, it can increase fastness.After 24-48hours,it can make a test about fastness.