亚洲一区二区精品,黄色软件视频免费,国产精品国产三级国产专不?,性福宝软件下载

一、適用

特光滑硅油布，絲光棉布，風衣布，防水尼龍布，普通尼龍布，羽絨服，莫代爾，雨傘布，泳衣布以及PU皮革等。

二、外觀組成及說明

◇ 外觀及組成：白色(半透明)狀粘稠體，聚氨酯聚合物

◇ 布氏粘度：80000~100000CPS

◇ PH值：7.0±0.5

◇ 固體含量：40%±1

三、特性

遮蓋力好、高光澤、水洗牢度好、高附著力、手刮不掉，手感柔軟、耐黃變、耐老化，印刷性能優，干濕擦達到4-5級（透明）。常溫下保存12個月，（避免45℃以上高溫或-25℃以下低溫）屬于環保型水性墨。（雙組份）

PU048-1A高牢度防水尼龍水性墨白（耐黃變、環保型）：牢度超好，附著力強，手刮不掉，耐黃變，耐老化，環保

PU048-1B高牢度防水尼龍水性墨透（耐黃變、環保型）：牢度超好，附著力強，手刮不掉，耐黃變，耐老化，環保，干濕擦達到4-5級

四、參考配方

五、操作流程

網紗80-100目印花 → 印2-3次2刀 → 烘干、干燥 → 熱處理 或過爐(150℃,3分鐘)

六、注意事項

由于面料多種多樣，在印花之前需要先行測試。在有涂層的布料上印花，需要測試布料涂層跟PU體系的粘結強度.。未確定情況使用或操作不當引起的質量問題本公司概不負責 。

Otherdetailedinformation

一．Substrates

smooth silicone oil cloth,mercerized cotton ,dust coat cloth,Waterproofnylon,general nylon,down jacket cloth,modal cloth,umbrella cloth,swimsuit cloth and PU leather.

二．Appearancecompositionandspecification

Appearanceandcomposition:white(translucent)viscousbody,polyurethanepolymer

Brinellviscosity:80000-100000CPS

PHvalue:7.0±0.5

Solidcontent:40%±1

三．Features

Good covering power,high glossiness,good wash fastness,high adhesion,using fingers to scrape will not off,soft hand feel,resistance to yellowing,aging,excellent performance of printing,the wet and dry rub reaches 4-5degree(clear),can be stored for 12 months at room temperature.(avoid temperature over 45℃ or below -25℃),it confirms to environmental protection (two component)

PU048-1A high fastness waterproof nylon waterbased ink white（resistance to yellowing/environmental）：super well fastness,high adhesion,using fingers to scrape it will not off,resistance to yellowing and aging,environmental.

PU048-1B high fastness waterproof nylon waterbased ink clear（resistance to yellowing/environmental）：super well fastness,high adhesion,using fingers to scrape it will not off,resistance to yellowing and aging,environmental.The wet and dry rub reaches 4-5 degree.

四．

五．Operationprocess

printingtechnology:80-100 meshscreenprinting-printing2-3times-drying-heattreatmentorheat

pressure(150℃，3minutes)

六．Note

Duetovariousfabrics,makingtestsbeforeprinting.printingonthecoatedcloths,shouldhaveatestaboutadhesionstrengthbetweencoatedfabricsandPUsystem.Usingoroperatinginuncertaincondition,ourcompanyisnotresponsibleforqualityproblem.